Welcome to the Taizhou city sound electronic technology limited company official website!
400-006-1982
PRODUCT
Location:HOME > PRODUCT
  • FUET-4020H

FUET-4020H

Name : FUET-4020H

Type : Electromagnetic Buzzer

Drive Mode : Passive Buzzer

Technology : Smd Buzzer

Size : 3-5mm

Description:

A. SCOPE 
This specification applies magnetic buzzer, FUET-4020H

B. SPECIFICATION

No.

Item

Unit

Specification

Condition

1

Oscillation Frequency

Hz

4000

Vo-p=1/2duty , square wave

2

Operating Voltage

Vo-p

2 ~ 4


3

Rated Voltage

Vo-p

3


4

Current Consumption

mA

MAX. 90

at Rated Voltage

5

Sound Pressure Level

dB

MIN. 70

at 10 cm at Rated Voltage

6

Coil Resistance

Ω

17±3


7

Operating Temperature

-20 ~ +70


8

Storage Temperature

-30 ~ +80


9

Dimension

mm

4.0 x 4.0 x H2.0

See appearance drawing

10

Weight (MAX)

gram

0.1


11

Housing Material


LCP( Black )


12

Leading Pin


 Tin Plated Brass(Sn)

See appearance drawing

13

Environmental  
Protection Regulation


 RoHS


 
C. APPEARANCE DRAWING  


Tol : ± 0.3      Unit: mm


D.TESTING METHOD    
Standard Measurement conditions
Temperature:25±2℃  Humidity:45-65%

Acoustic Characteristics:
The oscillation frequency, current consumption and sound pressure are measured by the measuring instruments shown below
 
In the measuring test, buzzer is placed as follows:
 
 
E. Typical Frequency Response Curve

 
 

F. Recommend Driving Circuit 
 
The base current Ib should high enough so that it saturates the collector current of the transistor with the CB load.

 

G. Soldering Condition
(1)Recommendable reflow soldering condition is as follows
(Reflow soldering is twice)
Note:It is requested that reflow soldering should be executed after heat of product goes down to normal.

  Heat resistant line
(Used when heat resistant reliability test is performed)
(2)Manual soldering
   Manual soldering temperature 350 oC within 5 sec.

 

H. RELIABILITY TEST

NO.

ITEM

TEST CONDITION AND REQUIREMENT

1

High Temperature
Test (Storage)

After being placed in a chamber with 802℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

2

Low Temperature
Test (Storage)

After being Placed in a chamber with -302℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

3

Humidity Test

After being Placed in a chamber with 90-95% R.H. at 402℃ for 96 hours and then being placed in normal condition for 2 hours.
Allowable variation of SPL after test: 10dB.

4

Temperature Cycle
Test

The part shall be subjected to 5 cycles. One cycle shall be consist of:  
Allowable variation of SPL after test: 10dB.

5

Drop Test

Drop on a hard wood board of 4cm thick, any directions ,6 times,at the height of 75cm .
Allowable variation of SPL after test: 10dB.

6

Vibration Test

After being applied vibration of amplitude of 1.5mm with 10 to 55 Hz band of vibration frequency to each of 3 perpendicular directions for 2 hours .
Allowable variation of SPL after test: 10dB.

7

Solderability
Test

Lead terminals are immersed in rosin for 5 seconds and then immersed in solder bath of +3005℃ for 31 seconds .
90% min. lead terminals shall be wet with solder
(Except the edge of terminals).

8

Terminal Strength
Pulling Test

The force of 9.8N(1.0kg) is applied to each terminal in axial direction for 10 seconds.
No visible damage and cutting off.

TEST CONDITION. 
Standard Test Condition        :      a) Temperature : +5 ~ +35℃     b) Humidity : 45-85%        c) Pressure : 860-1060mbar 
Judgment Test Condition      :      a) Temperature : +25 ± 2℃        b) Humidity : 60-70%        c) Pressure : 860-1060mbar 
 

I. PACKING STANDARD 


[return]

CLOSE
OPEN
  在線客服
风采好运彩3 惠泽社群一尾中特 甘肃麻将馆多少钱 六合彩资料软件 七乐彩走势图百度乐彩 贵州11选5胆拖投注 七星湖南棋牌下载安装 三d彩票中奖图示 重庆幸运农场规则 pt电子游艺娱乐平台 og平台与ogm平台 124期码报玄机图 棋牌游戏虚拟货币 重庆时时彩官方手机版 体彩七星彩走势图表 舟山体彩飞鱼开奖79期 捕鱼游戏图片